Press the “Up” or “Down” button until the desired day appears. Twist the knob to “Run.” Twist the GreenKeeper timer knob to “Watering Days.” Twist the dial to “Watering Days,” select the program you wish to set and press “Next” to set an interval schedule instead of an individual days schedule.

How do you set the watering days on a Toro GreenKeeper?

Press the “Up” or “Down” button until the desired day appears. Twist the knob to “Run.” Twist the GreenKeeper timer knob to “Watering Days.” Twist the dial to “Watering Days,” select the program you wish to set and press “Next” to set an interval schedule instead of an individual days schedule.

How do you set a Toro irrigation timer?

1. Turn the program dial to the “Auto/On” setting.
2. Slide the program switch to the zone you wish to program. …
3. Turn the Toro Sprinkler timer dial to the “Set Time/Day” position. …
4. Turn the dial to the “Set Watering Days” position.

How do I reset my sprinklers?

1. Turn the control dial to the “off” position.
2. Press the “next” button to access the clear-memory feature. …
3. Press and hold the “off” button until the display stops blinking.
4. Turn the control dial to the “run” position.
5. Press and hold down the “minus” arrow and “prog” buttons simultaneously.

How does a sprinkler controller work?

The stations send electrical impulses to their respective valves to open or shut them, letting water through to the sprinklers (or not). Because this works electronically, the controller has to be physically located near enough to the valves to allow for a wired hookup.

Why is my controller not starting the watering cycle?

Go to one of the irrigation valves and turn the solenoid 1/4 to 1/2 a turn counter-clockwise. … If the valve opens and sprinklers turn on, your valve is working and you’ll need to check the controller and field wiring. If the valve did not turn on any of the sprinklers, the water to the valves is still off.

👉 For more insights, check out this resource.

Why do my sprinklers come on twice?

A common reason why a program is repeating is that you have a second start time set. The start times control the exact time your ESP-Me timer will begin to water and they also control how many times a day your timer will water. The ESP-Me allows you to set up to 6 start times per program.

What does sprinkler Cal mean?

– Calendar and Interval Days. – 1 Min. to 4 Hrs. Zone Run Time. – 4 Start Times Per Day.

Why would a sprinkler zone not work?

Each zone consists of several sprinkler heads controlled by a valve that is electrically activated. If a single zone is not working, the problem is usually an electrical issue or a defective controller or solenoid.

👉 Discover more in this in-depth guide.

What is Toro GreenKeeper?

The Toro GreenKeeper is a programmable control unit that governs the operation of in-ground sprinkler systems. Once installed, homeowners can set the GreenKeeper to activate the sprinklers to water the lawn at predetermined times during the day or night.

Article first time published on

Where is my sprinkler timer located?

Often the valves are located inside one or more in-ground valve boxes. The tops of these boxes will be at ground level, and these, too, are usually fairly easy to spot and access. The valve box, or sometimes the valves themselves, are sometimes buried underground.

How do I know if my sprinkler system has a master valve?

It is connected to the “master” or “pump” connection in your controller. For Generation 1 controllers, this is the blue terminal in the wall mount. For Generation 2 controllers, find the terminal marked “M”. In the image below, the master valve is in the small circular box to the left of the main sprinkler box.

How long does irrigation controller last?

One of the components that you may need to replace regularly are the wires, often due to improper installation and corrosion. Valves will give you 10 to 15 years of service, while controllers 5 to 10 years.

What causes multiple irrigation zones to work at the same time?

5. Water is coming out of multiple zones at the same time: For the valves to stay open in one zone, while shutting outlets in other zones, there needs to be a minimum amount of water pushed through the valve. … To investigate further causes and solutions, go to our FAQ page and look under “Indexing Valves.”

How long does it take to set a sprinkler system?

A watering session should be long enough to soak the area sufficiently so all the roots receive a beneficial drink. Sprinklers should be set to run for about 30 to 35 minutes at a time twice a week. Your goal is at least 1″ of water a week for your lawn.

Why is my sprinkler system not getting water?

Your Sprinkler System Is Not Getting Water If the handle on your backflow valve gets inadvertently shut off, it restricts any water from flowing past the backflow and to the sprinkler system valves. Your rain sensor might be faulty. A wire might have been cut. The timer may be broken.